Life-fitness G4 Manual de usuario

G4 GYM SYSTEMASSEMBLY INSTRUCTIONSG4-001 / CLASS H / 09/19/08 / 8604101 / REV B-2

9ACE14DMBSTEP 5:• Carefully slide the RIGHT (N) and LEFT (M) REAR UPRIGHTS over the GUIDE RODS (AC) asshown in FIGURE 5 and SECURELY assemble the RIGH

10STEP 6:• SECURELY assemble the LEFT (D) and RIGHT (E) BOOM PLATES to the FRAME (A) using two3/8 X 3-3/4” BOLTS (6) and two 3/8” SILVER LOCK NUTS (1

11STEP 7:• Securely tighten all frame connections except the FOOTPLATE/FRAME connection as noted inFIGURE 7.• Slide the LEFT (F) and RIGHT (G) PEC FLY

12STEP 9:• Assemble the LEG PEDESTAL (K) to the FRAME (A) using two RH CAPS (32), one 1/2 X 104mm BOLT (2), two3/8” SHIM WASHERS (13), and one 1/2” L

13STEP10:• SECURELY assemble the SEAT PAD (AI) to the SEAT ADJUST (J) using two 3/8 X 3” SILVER BOLTS (10) and two3/8” WASHERS (18).• Assemble two ROL

14STEP 12:• Disassemble one of the BEARING BLOCKS from the PRESS ARM SUPPORT FRAME (X) andremove the PRESS ARM SUPPORT PIVOT as shown in FIGURE 12.• I

15STEP 13:• Disassemble the PRESS ARM PIVOT SHAFT from the PRESS ARM (H) by removing the two 3/8 X 3/4” ALLENSCREWS and two 3/8” FLAT WASHERS as shown

STEP 14:• Route the LAT CABLE (AM) through the FRAME (A) and assemble one 3-1/2” PULLEY (35) to theFRAME (A) using one 3/8” X 3-3/4” BOLT (6), two 3/8

STEP 15:• Route the LAT CABLE (AM) through the PRESS ARM SUPPORT FRAME (X) and assemble one3-1/2” PULLEY (35) to the FRAME PRESS ARM SUPPORT FRAME (X)

STEP 16:• Route the LAT CABLE (AM) through the PRESS ARM SUPPORT FRAME (X) and assemble one3-1/2” PULLEY (35) to the FRAME PRESS ARM SUPPORT FRAME (X)

1TABLE OF CONTENTSSafety Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

STEP 17:• Route the LAT CABLE (AM) around one 4-1/2” PULLEY (36) and assemble the PULLEY to theLEFT (D) and RIGHT (E) BOOM PLATES using one 3/8 X 3-3/

STEP 18:•Securely assemble the PEC FLY CABLE (AP) to the LEFT PEC ARM (F) as shown in FIGURE 18.• Assemble one 3-1/2” PULLEY (35) to the PEC PLATE (O)

STEP 19:• Screw the threaded end of the GUIDE CABLE (AO) into the end of the FLOATING PULLEYBRACKET (Z). Secure the CABLE GUIDE (23) in place with the

STEP 20:• Route the large ball end of the LOW CABLE (AN) around one V- PULLEY (37) and assemble thePULLEY to the FRAME (A) using two 3/8 X 3-3/4” BOLT

STEP 21:• Route the LOW CABLE (AN) around one 3-1/2” PULLEY (35) and assemble the PULLEY to thePULLEY BRACKET (Z) using one 3/8 X 1-3/4” BOLT (11) and

STEP 22:• Assemble one 3-1/2” PULLEY (35) to the FOOT PLATE (L) using one 3/8 X 3” BLACK BOLT (8),two STEP SPACERS 11/16” (27) and one 3/8” BLACK LOCK

STEP 23:• If upon completion of assembly, the HEAD PLATE (AF) does not sit on top of the first WEIGHTPLATE, push the HEAD PLATE (AF) down, insert the

STEP 24:• SECURELY assemble the TOP SHROUD BRACKET (3) to the RIGHT and LEFT BOOM PLATESusing two 3/8 X 2-1/2” BOLTS (7) and two 3/8” BLACK LOCK NUTS

STEP 25:• SECURELY assemble the LEFT SHROUD (1) and RIGHT SHROUD (2) to the TOP (3) and BOT-TOM (4) SHROUD BRACKETS using eight 3/8 X 1” BUTTON HEAD B

28MAINTENANCEOWe recommend cleaning your product (pads and frame) on a regular basis, using warmsoapy water. Touch-up paint can be purchased from your

INSPECTION1. DO NOT use or permit use of any equipment that is damaged and or has worn or broken parts. For all LIFEFITNESS equipment use only replace

29WARRANTYLife Fitness extends the following LIMITED WARRANTY to the original owner of the Life Fitness products. The Warrantyterms apply to IN HOME U

30CORPORATE HEADQUARTERS5100 North River RoadSchiller Park, Illinois 60176 • U.S.A.847.288.3300 • FAX: 847.288.3703800.735.3867 (Toll-free within U.S.

3IMPORTANT NOTESThank you for purchasing the Life Fitness G4 Gym System. Please read these instructions thor-oughly and keep them for future reference

4Minimum Required Usable SpaceMax User Weight = 300 pounds (136 kg)Length = 86 inches (219 cm) Width = 70 inches (178 cm)Height = 83 inches (211 cm)We

5PARTS LISTNote: Some of the parts listed may be pre-installed.COMPONENTS PARTS LISTKEYABCDEFGHIJKLMNOPQRSTUVWXYZAAABACADAEAFAGAHAIAJAKALAMANAOAPAQDE

6STEP 1:• LOOSELY assemble two BASE PLATES (C) to the FRAME (A) and BASE (B) using three 3/8 X3-3/4” BOLTS (6) and three 3/8” SILVER LOCK NUTS (19). S

7ASCHECK THAT THE WEIGHT PLATES (AS) AND HEAD PLATE (AF)ARE ASSEMBLED AS SHOWN IN FIGURES 2 & 3.FIGURE2FIGURE 3AF

8TSBOTTOMFIGURE 4STEP 4:• Place the GUIDE RODS (AC) through the BOTTOM SHROUD BRACKET and into the BASEFRAME (B) as shown in FIGURE 4.• Note: Lubricat